The Single Best Strategy To Use For h335 load data 223
The Single Best Strategy To Use For h335 load data 223
Blog Article
your cfe load is almost similar to mine, the one change is i utilised wolf magnum primers. as you probably know, it is vitally near the maximum load.
It is anecdotal, but for what its worth when comparing wc844 to tac both loaded to 5.fifty six pressures in a eleven.5 barrel, WC844 can make some pleasant fireballs the place with tac it is sort of non-existant. Presented where tac and h335 drop around the burn off level chart I might have thought it would've been the alternative.
Extensive load data for Hodgdon H335 reloading powder und complex requirements for this propellant.
Posted: five/3/2016 7:forty seven:48 AM EDT [#9] I have been attempting CFE223 with a few 55 grain bullets. Nonetheless dealing with it. I am able to say that It appears to "feed" pretty much. I've been making use of my Hornady Digital powder evaluate/scale although Doing work up my loads. The CFE223 feeds so quickly the powder measure can not precisely meter it (the Digital one particular). It offers me continual in excess of alarms. Even using the manner button to slow down the metering in excess of placing it in "gradual" isn't going to get the job done. I have not attempted it during the standard powder evaluate still but expect It could be very regular. I did, sort of Fortunate seriously, run throughout an extremely accurate BLC2 load a couple selection trips again.
It is always suggested to begin with “start off” loads and work up thoroughly to highest costs while cautiously waiting for signs of excess strain. The .308 Winchester can Establish pressures rather rapidly, so this warning should not be taken frivolously. A load that displays absolutely typical pressures, or pressures which have been within field tips, can soar rapidly earlier mentioned suggested ranges with the addition of just one or 2 grains of powder (or by switching case brands or perhaps lot quantities).
Does any one have knoledge of a printed recipie for molys and H335 or suggestions on a attainable new max load to work nearly?
Tend not to attempt to fix or modify any firearms depending on info on this Web page. Final Reloader, LLC and Generating With Metallic can't be held answerable for assets or own destruction on account of viewers/visitors of the Web page performing actions, treatments, strategies, or tactics explained in entire or section on this Site. By accepting these terms, you agree that you simply alone are entirely liable for your personal security and assets since it pertains to routines, strategies, strategies, or methods described in full or part on this Internet site.
Individually, my practical experience and impression of the two powders is practically the opposite of yours. CFE 223 will perform far better the for a longer time your barrel is as well as the heavier the bullet you utilize. My ideas are that CFE 223 is right on the verge of currently being as well slow of a powder to even use in 223.
This really is an more mature thread, you may not get a response, and will be reviving an aged thread. Make sure you consider developing a new thread.
Have normally heard that 335 metered good. Do TAC and Benchmark behave equally as well in the powder thrower? For that document I just bought a pound of Benchmark but it was a fairly easy alternative, only 223 ideal powder I could discover community.
Spherical powders require that more shot within the magnum for responsible ignition, a minimum of that's the speculation. I've normally utilized four hundred's in all my guns, such as with my ARs and have never experienced an issue either.
Stop chasing velocity and exceeding Max load data for H335 loads as H335 will return you damage to your gun and perhaps you, way too. It is exclusive in this regard, In accordance with this post.
I would like to check out other powders. Unfortunately, I have hardly ever found a can of CFE223 and it seems like it may be quite a while before I'll. The good thing is, I even now have here the most important Component of 8lbs. of H335 remaining. At 25gr per load, it'll still have a 12 months or two to make use of up.
The above mentioned feedback also apply to cup-and-core bullet patterns, as their construction, bearing surface area and seating depth may differ plenty of to change pressures of a given powder demand. At any time a bullet is substituted, begin with get started loads and do the job up carefully.